Eliminate dropped chains forever with the new OneUp Components Guide. As the trend for lower and slacker bikes continues, 'Little bikes' are getting more and more capable everyday. Revised for 2019 the OneUp Guide uses simple, one tool installation and adjustment as well as an all new tool less flip At only 40g the OneUp Chain Guide weighs less than a sip of water. WHY DO I NEED A GUIDE AND A NARROW WIDE CHAINRING? NW rings are awesome, but they're not perfect and every once in a while you can drop a chain while riding. On a social ride this means getting dropped by your friends. But when racing an Enduro a dropped chain can cost you the podium, which is why almost every EWS pro runs both a chainguide and narrow wide chainring. FEATURES - Tool less upper guide flip - Install without removing your crank - Single tool install and adjustment (4mm hex) - Boost compatible - Oval Compatible - Black Stainless Steel hardware - Patented US 10,053,188 Other Patents Pending SPECS - Weight: 40g - Capacity: 26-38T - Chainline: 7.5mm adjustment - Mount: ISCG05 - Color: Black top guide piece included - Material: 7075 aluminum, top guide glass reinforced thermoplastic

A BETTER REMOTE FOR ANY CABLE OPERATED DROPPER An Aluminum remote with an oversized bearing and a super smooth action. The unique lever position allows you to keep a stronger grip on the bars while actuating your post. Don't think twice about dropping your post, even when charging into technical sections. The OneUp lever mimics your R/H shifter’s inboard upshift paddle position instead of the usual downshift paddle position of most remotes. This position requires considerably less thumb movement to reach the lever. NO BLEEDING The cable setup is quick and easy. The cable clamps at the lever making shortening the housing length for clean routing a breeze. Unlike a hydraulically actuated dropper, there is no temperature sensitivity and If your remote gets damaged you can still lower or extend your post by removing it from your frame and pushing on the actuator by hand. - Kit includes cable and housing - Compatible with all cable actuated dropper posts.

This kit includes all the parts required to rebuild your V1 Dropper Post. - Replacement Seal - Upper and lower bushings - Anti-rotation pins - Compatible with V1 Dropper Post ONLY. We have found that ~95% of posts with slow top out were caused by low air pressure. Please make sure to check this first and do so with the post fully extended. Proper air pressure is 280-300psi at full extension, and the valve is located under the top clamp. If you are still having slow top out then there is a possibility that the upper white bushing needs replacement. This will be evident by the original bushing being difficult to reinstall after being removed.

Replacement dropper post remote body. - Does not contain cable, housing, or clamp bracket

V2 dropper remote clamp for 22.2mm handlebar.

Replacement dropper post remote clamp. Can be used to convert existing clamp on the OneUp Dropper Remote. - Compatible with Shimano I-SPEC-II brakes - Not Compatible with Shimano I-SPEC-A or B - Does not contain remote body.

Set of six oversized pins. All dropper posts require key way clearance. With so many different frames, clamps and ride heights it's not possible to ship play-free without running the risk of binding. The kit is meant to remove additional play that might develop over time or, for the more mechanically inclined, to tune the play out for a specific bike. Start with the 3 pins marked with 2 lines. If play still exists move to the 3 pins marked with 4 lines.

Eliminate dropped chains forever and add a touch of colour to your e-bike with the new OneUp Components STEPS Chain Guide. Available in 7 colours. The OneUp STEPS Chain Guide is lightweight and incredibly easy to install and use. The top guide has a tool-free flip feature that allows easy access to your chain for cleaning and maintenance. Top guide pieces are available in 6 bright colours to perfectly match your OneUp Composite Pedals, Grips and EDC Lite. Compatible with 32T to 38T chainrings. Weighs just 45g. FEATURES - Shimano STEPS E7000, E8000 and EP8 compatible - Includes black top guide piece. 6 other colours sold separately - Tool-less upper guide flip - Install without removing your cranks - Mounts directly to motor - Single tool install and adjustment (4mm hex) - Black Stainless-Steel hardware - Patented US 10,053,188 Other Patents Pending SPECS - Weight: 45g - Capacity: 32-38T - Chainline: 5mm adjustment - Mount: Shimano STEPS/EP8 - Colour: Black top guide piece included. Blue, Green, Orange, Purple, Red, Turquoise sold separately. - Material: Back Plate - 7075 aluminum, Top Guide - glass reinforced thermoplastic

SWITCH. A QUICK-CHANGE DIRECT MOUNT CHAINRING SYSTEM FROM ONEUP COMPONENTS. Switch was developed to reduce the cost of replacement chainrings, increase compatibility with new offsets and to make the process of changing your chainring much faster and simpler. - Cheaper Replacement Cost - Replacement rings are a fraction of the cost of a complete direct mount chainring - Quick Change - Replace your ring in less than an minute, using only a 4mm hex key. Tailor your gearing to the terrain that you're riding - Enduro World Series Champion Winning Narrow Wide tooth profile keeps your chain in place on the roughest terrain - 4 Ring Sizes (28, 30, 32, 34T) - 2 Profiles - both Round and Oval - 12 speed ring designed to work with all 8, 9, 10, 11, and both Shimano Hypergilde+ 12 and SRAM Eagle 12 speed chains. - Get ultimate traction with Oval rings by smoothing out the torque you deliver to your rear tire - Quick Change Rings can be replaced in less than a minute with only a 4mm allen key, without removing your crank. Simply loosen the bolts 2 turns, unlock the ring by rotating it by 20 degrees and pull it over and off your crank. Reverse these steps to install your new ring. If you plan to ride a trail that you know is steeper than your local trails, you can switch to a smaller ring in the parking lot, in less time than it takes your friend to put on his riding shoes! SPECS - Material: 7075-T6 - Weight: 69g (30T Oval) - Chainline: Standard is controlled by the crank. - Compatibility: Shimano direct mount XTR M9100, XT M8100, SLX M7100 series cranks. - Color: Black

- Replacement bolts for Switch carriers

Don’t get stuck between dropper sizes. The unique OneUp travel adjust shims allow you to custom tune your OneUp Components Dropper post by lowering the travel and extended length of your post by either 10mm or 20mm. A 180mm travel post can be reduced in travel to either 170mm or 160mm with this shim kit. Drop tuning can be done on-bike, tool free and without removing the saddle or touching a shock pump. Lowering the post travel also increases bushing overlap and alignment pin length, which is great for heavier riders. - 210mm Dropper Post - adjustable down to 190mm - 180mm Dropper Post - adjustable down to 160mm - 150mm Dropper Post - adjustable down to 130mm - 120mm Dropper Post - adjustable down to 100mm

Front Derailleur Mount for specific Salsa frame models. - Derailleur Mount Required for Direct Mount Front Derailleurs - Salsa Road Boost Front Derailleur Mount for 148 mm rear hub spacing - Enables installation of a braze-on front derailleur - Offset for 148 mm rear hub spacing - Replacement part for Cutthroat v2 frames - Wrap-around design provides additional derailleur stability - Interfaces with derailleur support bolt

Adapter to enable the use of Battery R. Booster on Silence eRIDE.

Spare hardware for our Fraser and Creston integrated cockpits.

Spare hardware for our Hixon integrated cockpits.

Specifically for the WTP Pathfinder sprocket.

Brake hardware for We The People bikes and frames. - MY2019 & MY2020 Frames With Pivot-3 System

Jagwire's Brake or Shift Cable Tips are made of lightweight, corrosion-resistant and durable aluminum and are the right size to nicely fit over the ends of up to 1.8mm-diameter cables. These caps are crimped in place on the cables to prevent fraying and ensure your cables last a long time. The tips come in colors to add a little style to your bike.

BB30 Spacer - 15.46mm

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss Shim Ring: for Star Ratchet Hubs with 26mm OD Driveside Bearings

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss 240s Shim Ring

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss Driver Spring - Ratchet EXP

Tight tolerances and precise torque specs mean precision parts like this MegaExo 12 Left Arm Crank Bolt need to be replaced from time to time. Make sure the heart of your drivetrain is secure, and pick up a spare or two today.

A traditional saddle clamp for use with vintage, older and inexpensive seatposts without an integrated clamp. - For use only with plain/pin-style seatposts that require a separate saddle clamping mechanism at the top - One bolt tightens the clamp to the rest of the seatpost and to the saddle rails at the same time. - 22.2mm / 7/8 fit with angle adjustment via serrated washers - Steel construction with ED black finish

- Noodle/Boot completely seal brake cable, upgrades most linear brakes

- Enough clamp bolts for 4 clamps

Aluminum headset stack spacers precision-cut to ensure proper headset function. - Precision-cut for proper function - Inner Diameter: 28.9mm - Outer Diameter: 34.4mm - Precision-machined aluminum

Replacement M5 x 8 Flat Head Screw fastener for derailleur hangers. - Thread: M5-0.8 - Overall Length: 8mm - Material: Steel - Use with 3mm hex wrench - Bag of 5

- 90 degree