Parts & Accessories

PIN KIT FOR OUR COMPOSITE PEDALS KIT CONTAINS: - 40 THREADED M3x10mm SOCKET HEAD PINS - 40 NYLOCK NUTS

- Protects cranks from damage caused by overtightening pedals - Can be used for bike fit adjustments, dependent on pedal thread length engagement

The Curve Sole Measurement Tool works in conjunction with the flat sole shims to correct the radius of flat sole shoes and prevent unwanted squeaking. There are 4 radius measurements, one per side, that measure the sole and indicate whether a shim is needed or not.

Shorter 7mm rear load pins for the outer extremities of SPOON, SPIKE, and OOZY pedals. - Provide durability and improved safety - Mix and match with the longer stock pins to customize your ideal amount of grip

Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.

Lost an end cap from your Penthouse Flat Mk5 Pedals? 2 x MK5 End Caps These also work for MK4 Penthouse flat pedals.

Longer rear load pins for the outer extremities of your pedals provide ultimate durability, while shorter front load center pins create a virtual concavity in the pin pattern, increasing grip without sacrificing pedal body thinness. - 28pcs rear load pins - 16pcs front load pins - Tool included

IGUS Bushing replacements for your Spike or Oozy pedals help to eliminate any play that develops over time, and revive smooth spinning action. - 2pcs IGUS self lubricating bushing - 2pcs O-ring - 2pcs stainless shim washer

Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs

Nylon toe clip straps, with zinc-plated steel quick-release buckles.

- Strapless resin construction - Strapless design - Tough and lightweight, ideal for urban conditions with frequent stops

- Double tongue resin toe-clips - Nylon straps with steel buckles

Replacement bearings and bushings specific to Spoon 90 (Small) and 100/110 (Medium and Large) pedals. Eliminates play that can develop over time, and revives performance. Includes: - Sealed Bearing x2pcs - 10mm IGUS Bushing x2pcs - Green Friction Seal x2pcs - Locknut - O-ring x 2pcs

Spare Pedal Pins for the Composite MK4 Pedals. Keep maximum traction on your pedals with new Pedal Pins. - 32 Pedal Pins - Enough for a pair of pedals - Used for MK4 Composite Pedals only

Crank Brothers' 5050 Pin Kit includes 40 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.

The KEO cleat covers are designed to protect your KEO cleats while walking. Compatible with KEO GRIP and KEO CLEAT, these covers lengthen the life of your cleats and improve safety when walking thanks to an anti-slip surface. - Compatibility: KEO Grip/KEO Cleat - Use: Protect the cleat

The Keo Spacer adaptors are slim wedges that fit between the shoe and the cleat. They aim to avoid the unpleasant creaking sound provoked by contact between the sole and the cleat, which can arise in particular with flat-soled shoes. Delivered with 2 spacers and 6 screws for quick and easy installation.

- Christophe Vintage leather strap - Celebrating 130 years of history - 370mm long - Metal buckle

HEIGHT ADJUSTMENT WASHERS AND PINS FOR OUR ALUMINUM PEDALS KIT CONTAINS - 40 - HEXIGONAL TIPPED M4 THREADED SOCKET HEAD PINS - 40 - 0.8mm THICK HEIGHT ADJUSTMENT WASHERS

Everything you need to fully rebuild your OneUp Composite Pedals. KIT CONTAINS - 2 CARTRIDGE OUTER BEARINGS - 2 INNER DU BEARINGS - 2 OUTER SEALS - 2 AXLE NUTS

- Set of 44 total replacement steel pins for vault pedals - Run threads-out for maximum traction or flip the pins to heads-out for less grip - 16 Short pins (for use in the center) overall length 8.5mm, stud is 4.5mm - 28 Long pins (for use in the outside edge) overall length 12.5mm, stud is 4.5mm - Use either a 5mm spanner or the included 2mm hex wrench to secure/remove

Spare Pedal Pins for the Penthouse Flat MK5 Pedals. Keep maximum traction on your pedals with new Pedal Pins. - 32 Stainless Steel Pedal Pins - Enough for a pair of pedals - Can be used for MK5 Penthouse flat pedals only

- Pedal Carbon blade Kit TIME XPro QTY 4

The Cleat Shim-Spacer helps compensate for leg length discrepancies.

The ATAC cleats are developed for the TIME mountain bike pedal range (MX and XC range). By switching right and left cleats, you can choose two options for the release angle: 13-degrees or 17-degrees. - Weight: 45g/pair

The ATAC Easy cleats are specifically for the mountain bike pedal and City Bike range of TIME (LINK, MX and XC range). The release angle of 10-degrees is easy for riders who want a quick step out. - Weight: 44g/pair

Replacement cleats for RXS pedals, featuring "Cafe" profiling, which means that when you walk into your local coffee shop for a mid-ride refreshment, you don't risk slipping and falling on the tile floor.

The Iclic fixed cleat works with all XPro and Xpresso pedals. This cleat is only available independently and is not included with new Xpro and Xpresso pedals. This is a zero-float cleat design, so there are zero (0) degrees of heel float and no lateral float along the pedal axle. It's compatible with all three-hole road shoes, but the included shim may be required for shoes that have a large curvature in the forefoot area. Full details are included in the easy-to-use instructions.

The Xpresso Fixed Cleats have been developed for the TIME Xpresso Road bike pedal range. They are designed for cyclists who prefer a secure feel with no angular or lateral float. The Bimaterial brings more durability when walking with the cleats. - Weight: 85g/pair

The Xpresso Free float cleats have been developed for the TIME Xpresso Road bike pedal range. They allow angular and lateral freedom in order to respect the natural movements of your legs and joints. You can also adjust the Q-factor (by switching the cleats), in order to optimize performance following 3 points: security, ergonomics and performance. The Bi-material brings more durability when walking with the cleats. - Weight: 85g/pair