Workstands

- Made of environmentally friendly plastic, TPR. - Spare part for Super B work stands: TB-WS20, TB-WS460, TB-WS30.

Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)

- Thru-axle adaptor for TB-WS10 Professional Race Workstand - Works with 15mm and 20mm front forks

TB-WS11 has deep wall compartments and various slots. Perfect for holding any tools and lubricants. Fits TB-WS10 workstand.

The PrepStand Pro Upgrade Kit makes measurement simple. It features a tray for weighing small parts and a hook for weighing larger items. This is a great upgrade for your Topeak PrepStand Pro.

Park's Work Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools and small parts close at hand. It has deep sides so your small items stay put and many slots for holding your tools. The Tool Tray fits Park's PRS-2, PRS-3, PRS-6, PRS-11, PRS-12, PCS-1 and PCS-4 repair stands.

A 6-inch (15cm) extension that easily mounts to the main beam of any PRS-22 or PRS-22.2 to accommodate longer wheelbase bikes with bottom bracket-to-front axle lengths over 28.75 inches, including CX, gravel and enduro style bikes.

The Topeak Tool Tray keeps tools and small parts close at hand for maximum convenience. And, it rotates for optimum accessibility, too.

Topeak's PrepStation Tool Tray attaches to their PrepStand repair stand (sold separately) to keep tools and small parts close at hand for maximum convenience. It's made of light and durable plastic with a padded bottom to hold tools in place, and it rotates for optimum accessibility.

Feedback Sports repair stands are the ultimate portable and home service partner for the most demanding mechanics. They’re ultralight, compact, and durable design delivers unmatched stability, adjustability and portability. Our Travel Bag collection is an awesome travel and protective companion for ensuring your stand looks new for years to come. Be the most popular rider at the trailhead with a Feedback Sports repair stand. Be the most popular mechanic at home with a brilliant storage bag. - Maximize the portability of your Feedback Sports repair stand - Protect your stand’s aluminum finish and your other equipment when traveling - Travel bag is water-resistant, durable and padded - Enough space for a Sprint Repair Stand and a Flop Stop - External window for business cards / ID card - Padded Velcro strap for comfortable carrying and transport - Full length, dual-zipper design - Rugged end-loops for vertical storage when not in use - 1-Year Warranty

The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Professional Race Stand. It makes travel easy and convenient, while also protecting your stand.

The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.

Topeak's sleek FlashStand Slim is a super parking/display stand that folds up for pocket-sized portability. This affordable, lightweight wonder securely holds your bike by the non-drive side crankarm to keep it upright and safe. Take it along in your jersey pocket for those quick pit stops, too!

Topeak's PrepStand Magnetic Tool Tray is a sturdy plastic tray with a magnetic metal bottom to keep steel tools and small parts close at hand for maximum convenience. It has a folding handle for portability and that also allows it to fit in Topeak's PrepStation (sold separately).

Topeak's PrepStand Tool Tray attaches to their PrepStand repair stand (sold separately) to keep tools and small parts close at hand and has divided compartments for maximum convenience. It's made of durable plastic and it rotates for optimum accessibility. It also has a translucent lid so nothing falls out and you can see what's inside without opening it.

Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.

Permanently and securely attach your Park Tool Repair Stand (sold separately) to the floor of your shop with Park's Floor Mounting Plate. Made with an 8" square of steel, it attaches to the stand with four bolts, which are included.

The PCS-EXT is an extension for the older pre-2001 repair stands. The kit includes a quick-release collar and extension tube to raise the working height of the stand. The PCS-EXT is required for use of the 106-AC (sold separately).

Park Tool's Repair Kit features the most common replacement parts for the 100-3C and 100-5C clamps. Includes: • 118s adjusting barrel • 117s eyebolt • 121s adjusting barrel pivot • 136 nut • 116s cap screws (2) • 108s-2 pins (2) • 107s-2 pin (1) • Washers (3) • E-clips (3)

Park's Truing Stand Upright Extensions are made of durable chrome-plated steel and have quick-releases so they install in seconds to your Park TS-2 Professional Truing Stand (sold separately). The Uprights allow the stand to be used with wheels with hubs up to 160mm wide (found on some tandems and downhill bikes), and 29-inch mountain-bike wheels. Plus, there are specially sized bosses that act as adapters to hold wheels with 20mm through-axle hubs, too.

For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Wheel Alignment Gauge (also called a dishing tool) is a must. It allows you to easily check centering on road, mountain and BMX wheels from 16 to 29 inches in diameter. It works with any hub width and its innovative design even allows it to be accurately used with the tire still on the wheel. The Wheel Alignment Gauge is a necessity for every wheelbuilder.

For extra protection of your favorite tools, Topeak's PrepStation Case Cover is made of 1000-denier nylon and EPE foam and slides perfectly over the PrepStation (sold separately). Even with it on, you can still unlock and extend the handle to move the case around quickly and easily.

Weight freaks rejoice! Topeak's Weight Scale is the perfect addition to your PrepStand Pro or PrepStand Elite. It quickly and accurately measures anything from small parts all the way up to bikes and wheels.

Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.

Park's adjustable linkage shop clamp is found in more shops than any other professional level clamp. The 100-3C features solid cast aluminum construction and durable replaceable clamp covers. Clamp has reliefs on both jaws for cable routing. - Fits all generations of PRS-2, PRS-3, and PRS-4 stands, and PRS-5 stands manufactured before 6/96 - Fits bike frame tubes from 1" to 1-5/8" (25mm to 41mm) - The clamp jaws are nominally 4 inches (10cm) wide - Uses 468B jaw covers

Park's Home Mechanic Wheel Truing Stand allows extremely accurate and reliable wheel truing and even building at an economical price. It's constructed from heavy-gauge steel and works with most wheel sizes and hub widths. It can be bolted to a bench for additional stability.

After years of research and testing, Park Tool's built what they consider the best shop clamp made. It’s smooth, versatile and built to stand up to everyday shop use. • #100-3D fits the following repair stands: PRS-2, PRS-2 OS, PRS-2 OS-1, PRS-2 OS-2, PRS-3, PRS-3 OS, PRS-3 OS-1, PRS-3 OS-2, PRS-3.2-1, PRS-3.2-2, PRS-4, PRS-4 OS, PRS-4 OS-1, PRS-4OS-2, PRS-4W and PRS-33 • #100-5D fits PCS-4, PRS-7, some models of PRS-5 (with composite top tubes), and PCS-1 models manufacturer post 2002. (Note: Inspect top tube below lever for an embossed "939") • #100-25D fits PRS-25, PCS-10, PCS-11, PCS-12 (and PRS-15 with 1951-15 Adaptor Stud) • Grips nearly any tube from 7/8” to 3” (23–76mm), including aero tubes • Micro-adjustability allows perfect clamping pressure every time and prevents damage to thin-walled tubes • Long travel cam handle allows quick entry, adjustment and exit • Versatile: It grips nearly any tube including aero shaped tubing and seat posts 7/8” to 3” (23mm-76mm). Its narrow clamping jaws (2.7”/7cm) are designed to clamp securely yet fit into tight areas or on short seat posts. • Durable, replaceable jaw covers • Soft Touch saddle cradle provides a perfect spot to temporarily rest a bike by its saddle • Built to last: Powder coated, precision machined, die-cast aluminum main body parts and high quality small parts • Fast operation: Cam-actuated adjustment system for quick entry, adjustment and exit, plus handy “spinner” handle helps speed large size range adjustments

Our patented Secure-Lock ratchet-action closure and push-button release clamp head, found on the award-winning Pro-Elite Repair Stand, became so popular we decided to make it compatible with steel bike shop repair stands. The versatile and patented 3.25? (8.3cm) wide clamp is capable of managing any bike frame, up to 2.6? (6.6cm). When you see the Pro-Elite Commercial Clamp upgrade in your bike shop, you know you’re in the presence of experts. NOTE: This is NOT a suitable upgrade for our folding tripod repair stands. Please contact Feedback directly to order the Pro Elite folding clamp head assembly.

Topeak's PrepStand Race securely holds bikes by cradling the bottom bracket and securing the fork with a quick release, and not by clamping the frame tubes or seatpost. This is ideal for bikes with ultra-light frames and seatposts, and for bikes with tight access areas that can't be clamped. For easy wrenching, this stand rotates horizontally 360 degrees, is adjustable up and down, and works with standard quick-release forks as well as through-axle forks. A vinyl-covered bottom-bracket cradle and velcro retention strap stabilize the bicycle so it stays put while you're wrenching. Plus, the low 10-pound weight makes it the ideal choice for traveling mechanics everywhere.

A versatile and convenient way to keep tools, supplies and technology at arms length on a PRS-33 Power Lift Repair Stand. The PRS-33TT solidly mounts directly to either side of the stand’s upright at any height. - 19 tool holding holes, slots and small trays in a variety of shapes and sizes - 14-inch (35cm) magnetic tool bar - Integrated mounting holes for PTH-1 Paper Towel Holder - Phone/tablet/clipboard holder - Pen and pencil holders - Adjustable utility hook to hang wheels, parts and scales - Height adjustable - Can be installed on a fully assembled stand