Parts & Accessories

With the Tacx tablet stand you can place your tablet at a comfortable height and distance while using your bike trainer. Adjustable to different tablet sizes - length 182-267mm, width 112-197mm, max. thickness 13mm.

Use this ANT+ antenna to connect an ANT+ trainer to your computer. That enables you to use computer software during your training sessions, such as the Tacx Trainer software, Zwift, and TrainerRoad. These programs read the training data transmitted by an ANT+ trainer and can control the trainer. It features a long cable so the receiver can be placed close to the trainer for an optimal reception without loss. The antenna is compatible with all trainers that communicate wirelessly via ANT+.

This mounts specifically to the Blendr system supported by Trek, which is similar to a GoPro interface. Featuring an accessory bolt hole pattern, it can be used with Stages accessories. - For Stages Dash L10, L50 and M50 - Fits Blendr-compatible stems - Works with Stages accessories, including GoPro attachment

This mounts specifically to the Blendr system supported by Trek, which is similar to a GoPro interface. - Designed to mount Dash above additional accessories or to the Blendr stem with a bottom attachment - For Stages Dash L10, L50 and M50 - Fits Blendr compatible stems

This mount fits most integrated bar/stem designs with a two-bolt interface below stem. - Mounts to a 2-bolt pattern (parallel to the direction of a stem) integrated handlebar (bolts not included) - Holds the dash level to the bars and in front of the bike. - For Stages Dash L10, L50 and M50 - Fits Shimano PRO and some Canyon integrated bars

Place Dash behind the bar for improved visibility and better protection from mishaps on the trail. - Mounts to the left of the stem, holds the Dash above the stem and bars such that a crash will not break the Dash - Has a plastic clamp that requires 2.5mm allen key to tighten to handlebars - Has rubber spacer so the mount can be used on 31.8mm bars. No accessories can be bolted to the bottom of the mount. - For Stages Dash L10, L50, and M50 - Compatible with 31.8mm and 35mm bars

Attaches Dash to steer tube beneath top cap. Great for mountain bikes and setups with minimal handlebar space. - Mounts to the top cap of a bike by replacing a headset spacer - Angle can be controlled by loosening and tightening the pivot bolt - For Stages Dash L10, L50, and M50 - Fits all 1-1/8" headsets with room for a spacer over the stem

This mount has accessory bolt holes on the bottom so it can be used with stages accessory attachments. - Mounts to the right TT bar, holds the dash in the center of the TT bars by tightening 2.5mm allen key head bolts - Can fit smaller 22mm bars using a rubber spacer (included) - Height, and therefore, bar clearance can be controlled by adjusting the pivot screw. - For Stages Dash L10, L50 and M50 - Compatible with 24mm and 22mm aero extensions - Fits a wide range of aero bars and includes a pivot for multiple placement options and ideal viewing angle

Stages magnet-free Cadence sensors fit to your crank arm and rear hub to provide real-time, accelerometer-based cadence data to your cyclometer or phone via ANT+ and Bluetooth Smart. - Compatible with most crank arms - Installs/removes in seconds - IPX7 Water-resistant - Super light—just 8 grams - Runtime: 600 hours - Operating range: 18-200 rpm - Blue and red LEDs indicate pairing, activation, and low battery status

Stages magnet-free Speed sensors fit to your hub to provide real-time, accelerometer-based speed data to your cyclometer or phone via ANT+ and Bluetooth Smart. - Compatible with most wheels - Installs/removes in seconds - IPX7 Water Resistant - Super light—just 8 grams - Runtime: 600 hours - Operating range: 2-60 mph - Blue and red LEDs indicate pairing, activation, and low battery status

The Stages Spindles "G" bottom bracket spindle allows the retrofit of the carbon Stages Power meter for SRAM BB30 DUB MTB cranksets. The spindle is manufactured for Stages Cycling by Full Speed Ahead, forged and machined out of aluminum to allow for the carbon Stages Power meter for FSA 386 EVO and Stages Carbon 30mm model to be used with SRAM DUB MTB. The Stages Power meter 30mm spindle is specifically designed to meet or exceed the performance of the manufacturer's stock component, while allowing the retrofit of the new carbon Stages Power Meter to a rider's SRAM drivetrain. - Spindle only

- Di2 internal battery, fits all e-Tube Di2 groups - Capacity: 500 mAH (± 2000km) - Use with EW-WU101 or SC-MT800 interfaces/junction to gain BlueTooth Smart wireless connectivity for on-the-fly adjustments with smartphones and tablets - Requires SM-BCR2 charger

The new DN300 Built-In type battery features the same waterproof design that Di2 users have loved for generations. Now with 3 ports, it delivers stable power to Shimano's 12-speed road derailleurs (and shifters if a fully wired option is selected). - Compatible with thinner next-generation electric wire SD300 and systems after R9250/R8150 series - Li-Ion type - Capacity: 500 mAH |3.7Wh (± 2000km autonomy) - Rated voltage: 7.4V - Charges through RD-R9250 |RD-R8150 rear derailleur using EW-EC300 Di2 Charging Cable (sold separately) - Fixing small parts included - Weight: 52g

Shimano BT-R1A External Di2 Battery - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware - Di2 External Battery, battery charger, and power cable are universal between Dura-Ace 9070, 7970, Ultegra 6870, 6770 and Alfine Di2 systems - Battery weight: 71 grams

Replacement/Spare Part – UNI-GO2 GoPro Adapter Bracket Allows mounting of Serfas headlights to GoPro action camera mount systems (e.g. helmet mount, handlebar mount, etc.) - Compatible with all current E-Lume and late model True Series headlights

3-IN-1 Handlebar Mounted Accessory Holder: 3-IN-1 Design: - Headlights - Action Cameras (GoPro) - Garmin Computers (Compatible w/ Garmin Only) - Adjustable Angle (100 Degree Tilt Up/Down) - Materials: Aluminum Alloy, Nylon - Simple Installation Specs: - Length: 105mm - Width: 68mm - Height: 57mm - Weight: 76g - Snap Ring Fitment: 31.8-32mm Bars - Max Load: 400g

The QuickView was designed to put the Garmin Edge Computer out in front of the stem. Fits Garmin 605 and 705. - Glass-filled nylon, stainless steel Torx T25 bolt - Weight: 20g

- Shift buttons mounted to the end of a bar plug - Included wire connects to Blip Box - Fits bars with 19 - 20.5mm inside diameter

Be it the fireworks of a finale, an ideal rhythm, climbing on the top, or a deep, dark place extracting the last kilojoule of effort on your bike split, you want to adjust your gear with the twitch of a finger. eTap Blip satellite shifters allow you to shift when you want, where you want. - Limitless remote shifting positions for drop and aero bars - Wired shift buttons can be positioned however the rider prefers - Connect to Blip Box or drop bar eTap levers - Compatible with SRAM RED eTap shift/brake controls

SRAM eTap batteries are literally a snap to remove and charge. Just flip the tool-free battery latch up and slide the battery up and out of the derailleur. Then snap the battery into the USB powered charger and connect the charger to any USB power source or A/C USB adaptor. A full charge takes just 45 minutes to complete. - Finish: Black - Compatibility: SRAM RED eTap

Significantly smaller, the SRAM eTap AXS BlipBox is now easier to integrate — mounting inside a stem faceplate cap, feed box, or frame. It's also AXS enabled, for easy personalization. Simple, intuitive, aero. - Replaces standard drop bar shift levers - Simple and intuitive eTap shift logic - AXS enabled for easy personalization - Limitless aero configurations - Two ports per side for Blips - Fits the included optional stem mount - Compatible with existing eTap Blips and Clics - Mounts inside stem faceplate cap, feed box or frame

SRAM eTap Battery is the power source for the eTap system. The same power unit is interchangeable between front and rear derailleurs. - Up to 1000 kilometers of riding per charge - Weight: 24g - Finish: Black - Compatibility: SRAM RED eTap

- Use to keep Blips in place on handlebars - Fits 31.8mm round portion of drop bar - Clamp mounts directly to bar outside of tape zone - Ideal for use with thumbs or index fingers while hands are on the tops - Right and left specific, just like Blips - Weight: 12 grams (for pair) - Material: Polypropylene - Compatibility: 11-speed - Recommended Group: SRAM RED eTap

External Blip mount for aero extensions and base bars - 360 degree rotation for adjustment - Aero use only to fit 22.2mm OD bar 65mm in length - Fits all Zipp aero extensions and base bars - Blips not included - Weight: 57 grams for pair (does not include Blip) - Material: Polypropylene + TPE - Compatibility: 11-speed - Recommended Group: SRAM RED eTap

MORE POWER, WITH SECURITY, MORE COMFORT. Water-repellent mobile phone case for the bicycle handlebar Everything in view - in any weather: The smartphone case COM/SMARTBAG can be attached to any COMPIT cell phone holder thanks to the adapter. A special COMPIT cover is therefore not necessary. The large transparent window ensures that the touchscreen is easy to operate, and it is also possible to unlock the cell phone with a fingerprint directly through the film. The lower extra compartment not only offers additional storage space for keys and money, but also space for the COM/UNIT power bank for inductive charging of the mobile phone while driving. For attachment to the COMPIT mobile phone holder system When touring in rough terrain, it is advisable to charge the cell phone with a cable. Optionally, the COM/UNIT can also be attached directly under the SMARTBAG to the COMPIT smartphone holder. In this case, the mobile phone must always be charged via cable through the cable guide. Suitable for smartphones with a maximum size of 155 x 80 x 15 mm. - Only compatible with the COMPIT system - Extra storage space - Water-repellent - Can be operated through foil - For all common smartphones - Weight: 115g

COMPIT Phone Covers (or the COMPIT Phone Adapter) are needed to securely mount the phone to the COMPIT unit. The cover has a special mounting device that allows the phone to be docked into the COMPIT system. Enclosing the outer edges of the phone and extra-durable at the points of maximum stress, this cover is made of shock-absorbing, high-quality, wear-resistant plastic. It can be easily attached and removed from the phone. - For iPhone 11 Pro

COMPIT Phone Covers (or the COMPIT Phone Adapter) are needed to securely mount the phone to the COMPIT unit. The cover has a special mounting device that allows the phone to be docked into the COMPIT system. Enclosing the outer edges of the phone and extra-durable at the points of maximum stress, this cover is made of shock-absorbing, high-quality, wear-resistant plastic. It can be easily attached and removed from the phone. - For iPhone 6+/7+/8+

COMPIT Phone Covers (or the COMPIT Phone Adapter) are needed to securely mount the phone to the COMPIT unit. The cover has a special mounting device that allows the phone to be docked into the COMPIT system. Enclosing the outer edges of the phone and extra-durable at the points of maximum stress, this cover is made of shock-absorbing, high-quality, wear-resistant plastic. It can be easily attached and removed from the phone. - For iPhone 6/7/8

COMPIT Phone Covers (or the COMPIT Phone Adapter) are needed to securely mount the phone to the COMPIT unit. The cover has a special mounting device that allows the phone to be docked into the COMPIT system. Enclosing the outer edges of the phone and extra-durable at the points of maximum stress, this cover is made of shock-absorbing, high-quality, wear-resistant plastic. It can be easily attached and removed from the phone. - For iPhone X/XS

COMPIT Phone Covers (or the COMPIT Phone Adapter) are needed to securely mount the phone to the COMPIT unit. The cover has a special mounting device that allows the phone to be docked into the COMPIT system. Enclosing the outer edges of the phone and extra-durable at the points of maximum stress, this cover is made of shock-absorbing, high-quality, wear-resistant plastic. It can be easily attached and removed from the phone. - For iPhone XR/11