Tools/Maintenance

Wrench for adjusting hub-end nipples on 3T Mercurio wheels.

The ideal trail-side repair kit. - Contains 6 patches, 1 metal buffer, 2 tire levers and 1 tube of rubber cement

Supports bikes at the seat and chain stays - Lifts rear wheel to allow maintenance and repair of drive-train - Adjustable hook height and angle - Stable wide footprint

Replacement threaded cap for Abbey Hanger Alligment Gauge Tool.

Replacement shaft for Micro Bearing Press - 1/4" shaft diameter - 12" length

The soft face on the Titanium Hammer is destined to be gouged, get worn down, or even melt (if you leave it near heat). Replacement soft face for Abbey Titanium Hammer.

Replacement ESI Grip for the Titanium Hammer laser engraved with the Abbey Logo.

Replacement pins, these are original equipment chain pins for our chain tool, they also work as an alternate to the Campagnolo UT-CN300 11spd chain tool, Shimano CN-34 and CN-32 Sold in pairs.

For use with 1/4" Micro Bearing Press Shaft

Replacement feeler gauge for the Abbey Hanger Alligment Gauge Tool.

For use with 1/4" Micro Bearing Press Shaft

The soft face on the Shop Hammer is destined to be gouged, get worn down, or even melt (if you leave it near heat). Replacement soft face for Abbey Shop Hammer.

Replacement shaft for Modular Bearing Press

For use with 1/2" Bearing Press Shaft

For use with 1/2" Bearing Press Shaft

For use with 1/2" Micro Bearing Press Shaft

Replacement 6/8mm Hex bit for both the Abbey BBQ Wood Handled Pedal Wrench and the Team Issue Pedal Wrench.

For use with 1/2" Modular Bearing Press Shaft

Replacement shaft for Micro Bearing Press - 1/4" Diameter Shaft - 24" length

1/8" mid plate, needed to use the Decade chain tool with wide 1/8" track and single speed chains.

For use with the Decade Chain Tool this AXS Mid Plate is required for the SRAM AXS Road and the new MTB Transmission Flat Top chains. This part is not needed for other 12spd chains from various manufacturers. The mid plate is visually differentiated from the other Decade mid plates by three dots on the face of the plate.

For use with 1/4" Micro Bearing Press Shaft ID = 10mm OD = 26mm

For use with 1/4" Micro Bearing Press Shaft ID = 12mm OD = 28mm

For use with 1/4" Micro Bearing Press Shaft ID = 8mm OD = 22mm

For use with 1/4" Micro Bearing Press Shaft ID = 9mm OD = 22mm

For use with 1/4" Micro Bearing Press Shaft ID = 9mm OD = 24mm

For use with 1/4" Micro Bearing Press Shaft ID = 9mm OD = 20mm

For use with 1/4" Micro Bearing Press Shaft ID = 12mm OD = 18mm

For use with 1/4" Micro Bearing Press Shaft ID = 10mm OD = 19mm

For use with 1/4" Micro Bearing Press Shaft ID = 12mm OD = 21mm

For use with 1/4" Micro Bearing Press Shaft ID = 15mm OD = 24mm

For use with 1/4" Micro Bearing Press Shaft ID = 8mm OD = 16mm

For use with 1/4" Micro Bearing Press Shaft ID = 10mm OD = 22mm

For use with 1/4" Micro Bearing Press Shaft ID = 12mm OD = 24mm

For use with 1/4" Micro Bearing Press Shaft ID = 15mm OD = 28mm

The Brass Face for the Shop Hammer is a fantastic option when hammering on metal and you need something softer than the material your are pounding on.

The Stu Stick is a 44-gram rotor truing tool. Whether you want to slip it into your hydration pack for that enduro mountain bike ride or travel the world working with one of the staples of cross racing, it's up to the task. You can even use it to crack open a beer after you're done with the day's fun. - Weight: 44g - Made of aluminum

Replacement shaft for Modular Bearing Press

These gems are machined to precisely fit the preload adjuster cap on all modern 24mm spindle Shimano cranks. The finger spline offers good leverage to install, remove, or adjust the preload cap. We also added a 5mm hex in the center should you need a little extra leverage that a hex key provides. These are also compatible with our fit kits and with the addition of a saddle height bullet can be used to more accurately measure saddle height.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. The Fork Seal Press is built with modern tight fitting fork seals in mind. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.

Suspension service is a specialty within bicycle repair, and it takes specialized tools to perform this work. One of the things that any factory tech will tell you is nice to have are sockets specifically made or altered for the low profile hex on the top of each fork leg. The lead-in or chamfer on a standard socket will greatly decrease the contact between tool and part and can easily scratch or deform those nuts. For years shops have been grinding down their sockets to remove the chamfer. The problem is that you're still often left with a loose-fitting socket that is still prone to chewing up those delicate parts. That's why we started from scratch. We made our sockets from billet aluminum to exacting tolerances to keep these parts in good shape. Fully CNC-machined with zero lead-in, they make the specialty that is suspension service a little bit easier. They feature a 3/8" square drive for use with your favorite torque wrench as well as finger splines to help run the top caps into the fork legs with those oil soaked hands. We also kept them short (1" or 25mm for all sizes) to reduce the chance of them slipping off of the top cap under torque. - Made from billet aluminum to exacting tolerances to keep form damaging the suspension - Finger splines so you can thread it easily by hand - 3/8" square drive - Short (1"/25mm for all sizes) to reduce the chance of them coming off of the top cap under torque - Made in Bend, Oregon Applications - 24mm socket - used on SRAM top caps - 26mm socket - used on Marzocchi and Reverb sealheads - 27mm socket - used on Fox and X-Fusion top caps - 30mm socket - used on the RS-1 SRAM sealhead removal tool as well as a handful of other forks. - 6-size set covers most modern suspension forks on the market: 24, 26, 27, 28, 30 and 32mm

This simple tool is designed to remove and install the static bearing in the shock ends of many modern rear shocks. Machined from durable stainless steel this compact tool allows the user to remove and install the DU bushings without resorting to hammers and punches. The coarse acme thread keeps the constant turning to a minimum.

For use with 1/2" Bearing Press Shaft ID = 15mm OD = 26mm

For use with 1/2" Bearing Press Shaft ID = 17mm OD = 28mm

For use with 1/2" Bearing Press Shaft ID = 24mm

For use with 1/2" Bearing Press Shaft ID = 15mm OD = 21mm

For use with 1/2" Bearing Press Shaft ID = 17mm OD = 23mm

For use with 1/2" Bearing Press Shaft ID = 20mm OD = 27mm

For use with 1/2" Bearing Press Shaft ID = 17mm OD = 26mm

For use with 1/2" Bearing Press Shaft ID = 20mm OD = 32mm

For use with 1/2" Bearing Press Shaft

For use with 1/2" Bearing Press Shaft ID = 15mm OD = 28mm

For use with 1/2" Bearing Press Shaft ID = 18mm OD = 30mm

For use with 1/2" Bearing Press Shaft ID = 20mm OD = 37mm